Yes, we do have plug-n-play wiring options to provide towed vehicle lights and trailer lights on your 2015 Jeep Wrangler. You will want to use the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118416 and the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM56200.
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118416 would plug into the plug behind the drivers side tail light and then the Hopkins Custom Tail Light Wiring Kit for Towed... view full answer...
I do have another product for you as the Vehicle to Vehicle Tail Light Converter # 118158 is only for going from a vehicle with combined tail lights to a vehicle being towed that has separate tail lights and turn signals.
The Upgraded Circuit Protected Tail Light Converter # 119178 will connect to your car that has separate turn signals and brake lights and combines them to for the 2nd vehicle with combined tail light/turn signals. This has a 4-way flat connector like that is used on... view full answer...
It sounds like you need a converter so the 3 wire system on your vehicle works with the 2 wire system on your new LED tail lights. If that is the case, you can use the Hopkins Tail Light Converter - LED Compatible # HM48847. This installs on your vehicle wiring to combine your vehicle's independent brake light and turn signal functions. view full answer...
The only 60 inch long LED light strip we offer would be # A80170. The strip would be tapped into the vehicle wiring, like the running light circuit and would be powered by the vehicle battery. We offer a few LED light strips that are powered by their own battery packs, but they are much shorter at 18 inches.
If you click the provided link, you can see the LED light strips we have available. view full answer...
In order to prevent the trailer hitch third brake light on your 2000 Chevrolet Blazer from flashing when using the turn signals, you will need to install the Vehicle to Vehicle Taillight Converter, # 118158. This converter will work with the LED trailer hitch brake light. LED lights are only a concern if they are on the vehicle and the converter draws power from them.
The Vehicle to Vehicle Taillight Converter, # 118158, separates the signals so the third brake light will only illuminate... view full answer...
The exact thing that you just described is the Custer Wireless LED Tow Light # LIW-LDTL.
It uses magnets to install on the towed vehicle and has a rechargeable battery so you to not have to purchase AA or AAA batteries to power it. For the light functions to work you will simply need to plug in the wireless transmitter to the 7-Way on the back or your RV or tow vehicle and then flip the switch to the "on" position on the light bar. Since this is made to be installed on the top of a towed... view full answer...
We do offer a wide range of accessory fog light kits for vehicles like your 2008 RAV4. Some of these are vehicle-specific kits but others are general-purpose kits that can fit a wide range of vehicles.
You can use the link provided to see all available options, such as the Optronics Halogen Fog Light Kit # QH-84CF. This kits features clear lens 5- x 2-3/8-inch lights, mounting brackets, wiring and hardware.
You can simply click on each item to reviews its specifications and pricing. view full answer...
I currently show 2 wiring harnesses for a 2011 Toyota Sienna. First, from CURT, we have the Circuit Protected T-Connector Vehicle Wiring Harness, # C56106. I have included a link to the installation instructions for you.
The other is the Tow Ready T-One Connector w/Upgraded Circuit Protected ModuLite, # 118498. I have included a link to the installation details and a link to a video showing a typical installation for you.
Both of the available wiring harnesses connect to the vehicle and... view full answer...
I would recommend to use the Mighty Cord 4-Way to 6-Way Adapter, part # A10-6034VP.
If you only want to use the basic lighting functions provided by the 4-Way (left/right turn, brake, and running lights) then all you will need to do is plug the 4-Way end of the # A10-6034VP adapter, into the vehicle 4-Way. The trailer 6-Way will then plug into the 6-Way receptacle on the adapter. You will also need to ground the white wire on the adapter to the vehicle frame at a clean and corrosion free... view full answer...
We do not have OEM type vehicle wiring connectors but you can make a spliced connection to your 2005 Sierra's 3rd brake light wire using a Quick-Splice connector such as # SWC501915-1. These allow you to tap into that vehicle wire's brake light switch signal which is sometimes required for hardwired brake controller installations. view full answer...
If your 2003 Toyota Tacoma is a Xtra Cab 4WD 2 Dr. you can use the Westin Molded Lighted Step Boards with Custom Install Kit, part # 27-0005-1085. If your vehicle is the 2003 Toyota Tacoma Double Cab you can use the Westin Molded Lighted Step Boards with Custom Install Kit, part # 27-0015-1605.
There are some non-lighted steps or boards that are cheaper than the lighted steps or boards and some higher quality non-lighted steps or boards that are more expensive. It seems to vary it just... view full answer...
For your 2000 Audi TT Quattro I will have LED replacement lights available for the exterior lighting of your vehicle like the Putco 1156 LED Bulb, part # P231156A360, that you have referenced. This LED bulb will fit your rear turn signal.
I am including a link to a product page that will list the available replacement LED lights for your vehicle. A load resistor kit # P230004A-2, is required when switching to LED bulbs for turn signals.
I do not have any replacement LED bulbs for the... view full answer...
Here is a list of the different bulb and socket kits we currently offer.
Roadmaster Tail Light Wiring Kit with Bulbs # RM-155
Blue Ox Tail Light Wiring Kit - Bulb and Socket # BX8869
Roadmaster Tail Light Wiring Kit w/ 7-Way to 6-Wire Connector - LED Bulb and Socket - Red # RM-152-LED-7
Roadmaster Tail Light Wiring Kit for Towed Vehicles - LED Bulb and Socket - Red # RM-152-LED
Blue Ox Tail Light Wiring Kit for Towed Vehicles - Integrated LED Bulb and Socket - White # BX88269
Blue Ox... view full answer...
You can use Curt wiring harness # C55504 which plugs in line with the tail light wiring on your 2004 Dodge Ram 3500. This will bypass the tow package wiring and provide light functions only at its 4-Way connector which you could either keep or cut off to wire the remaining wires to the back of a 7-Way connector if that is what you have.
On this Curt harness the white wire is ground, brown is running lights, yellow is left turn/brake lights, and green is right turn/brake lights. view full answer...
Curt offers a custom-fit adapter for the 2006 Porsche Cayenne that includes load resistors to allow the vehicle to pull a trailer with LED lighting. That item is part # C57003 and it is shown in the linked video. This adapter includes load resistors to allow vehicles like the Cayenne to properly activate LED trailer lights. view full answer...
I have a solution for you, but the problem you're going to run into is going to be that most light bars that don't require drilling are mounted to either an aftermarket bumper that has light attachment points or spans the width of the vehicle and attaches via brackets that utilize pre-drilled holes/screws on the vehicle. I notice you were looking at the Buyer's Products 3rd Brake Light Mount # 3378895350, but we unfortunately do not have one that is designed to fit on the 2019 Ford F-350's... view full answer...
Since there really isn't a great way to install a removable style of tow bar lighting to your 1989 Jeep Wrangler your best option is going to be to install a diode kit style of lighting.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install... view full answer...
The circuitry for strobe lights # PRS70726 is not sophisticated enough to allow for alternate flashing of amber and white lights and it only has white lights. What I recommend is one amber set, such as # ALP77234, and one that is all white lights such as # PRS70726. view full answer...
We do offer replacement bulbs for the various lighting functions on the vehicle. All replacements for each type of light are shown on the linked page. These include halogen and LED replacements. LED lights are gaining popularity since their prices have come down over recent years, plus they offer the benefits of reduced power consumption, less waste heat and longer working lifespans.
As an example, the LUMA LED headlight bulbs # HL-9005C-2G6 work on your headlights as either low beam or... view full answer...
It will depend on what you have as a normal round trailer connection on your vehicle. There is a 4 Round, 6 Round and a 7-Way Round connector.
If you have a round 7-Way Round connector on your tow vehicle and you are wanting to connect the 4-flat connector on the cargo carrier light kit, # 20174, to it, you can use the Hopkins Heavy-Duty Trailer Coiled Wire Adapter for 7-Way to 4-Wire Flat, # HM47065.
If you have a 4 round plug on your vehicle you can use the Hopkins Adapter 4 Round... view full answer...
Go To Results